1.電機運轉不正常，有連續嗡嗡聲。主要是因?yàn)槎噙\(yùn)行，唯一的辦法就是先檢查動力回路接通三相。
      The 1 motor operation is not normal, continuous hum. Mainly because of two phase operation, the only way is to check the power circuit connected to three-phase.
    2.閥門卡死，導致的原因可能是反向旋轉和限位開關調整得不正確，解決方法是在閥門開啟位置時，使用手輪操作中的錘擊機構能打開卡死的閥門。
      The 2 valve stuck, can result from reverse rotation and limit switch not adjusted right, the solution is in the valve open position, click mechanism can open the death card using the handwheel operation of the valve hammer.
    3.執行機構旋轉，但沒有驅動閥門。導致原因離合器桿掛鎖在“手動”位置和動軸套位子沒有對好。解決方法有離合器打到“遠操”和對好軸套位置。
      3 actuator rotation, but not to drive the valve. Causes the clutch lever padlock in the "manual" position and the movable shaft sleeve seat is not good. The solutions of clutch hitting "remote operation" and good shaft position.
    4.閥門沒有到位電機就停止運轉。導致原因行程控制器調整不良，轉矩控制器提前動作。
       The 4 valve did not reach the designated position motor stops running. The cause of stroke controller adjust the bad, torque controller early action.
    5.轉矩、行程開關不起作用失控。導致根源相序接錯、線路接錯、接觸器吸鐵不釋放。解決方法是調換電機相序、檢查線路糾正錯誤、清潔或調換接觸器。
      The 5 torque and stroke switch does not work out. Root cause of phase sequence connection fault, fault line access, contactor iron absorption does not release. The solution is to replace the motor phase, check line to correct the error, clean or replace the contactor.
車庫門使用注意
Garage door use note
很多時候廣大消費者沒有注意日常使用的安全，以為車庫門的安全性很高，并不會發生什么意外，出于安全著想，大家使用車庫門注意事項
     When a lot of consumers did not pay attention to safe for daily use, the safety that garage door is very high, and will not happen any accident, for the sake of safety, we use the garage door note
1)收到遙控器及鑰匙后請安裝人員演示遙控器及手動鑰匙開關門。
1) received from the remote controller and key please installation personnel demonstration of remote control and manual key switch door.
2)安裝完成后務必請安裝人員對門體進行調試運行，運行順暢后方可交接遙控器及鑰匙，保修卡。
   2) after the completion of the installation must install personnel door body debugging and running, running smoothly before handing over the remote controller and key, warranty card.
3) 禁止在看不到門體運行情況的地方操作遙控器，以免造成安全事故或車庫門誤開。
3) is forbidden in the local remote control operation can not see the door body running conditions, so as to avoid safety accident or garage door opened by mistake.
4)門體正在運行時，嚴禁人或物體從門體下方通過，或在門體下方停留。
    the door body is running, it is strictly prohibited to people or objects through from the door body below, or stay under the door body.